{"product_id":"t-h-marine-hot-foot-john-evin-merc-t-h-hf-1","title":"T-H Marine Hot Foot - John. Evin. Merc.","description":"\u003ch2\u003eT-H Marine Hot Foot Original Foot Throttle\u003c\/h2\u003e \u003cp\u003eThe T-H Marine Hot Foot Original Foot Throttle allows you to drive your boat like your car. With this foot throttle, you keep both hands on the wheel and control the throttle with your foot. If your foot is removed, the throttle returns to idle, allowing for safe operation of high performance boats. The T-H Marine Hot Foot has been the number one throttle on the market for 30+ years. It improves throttle control for all outboard and inboard engines. The all cast aluminum construction with stainless steel hardware makes this unit lightweight and resistant to corrosion. The non-sticking Teflon and Nylon bearing surfaces provide trouble-free operation.\u003c\/p\u003e \u003cp\u003e\u003cstrong\u003eFeatures:\u003c\/strong\u003e\u003c\/p\u003e \u003cul\u003e \u003cli\u003eProvides added safety and performance\u003c\/li\u003e \u003cli\u003eImproves throttle control for all outboards and inboards\u003c\/li\u003e \u003cli\u003eAll cast aluminum and stainless steel hardware\u003c\/li\u003e \u003cli\u003eLightweight and resistant to corrosion\u003c\/li\u003e \u003cli\u003eNon-sticking Teflon and Nylon bearing surfaces\u003c\/li\u003e \u003cli\u003eNylon and Teflon bushings on all critical pivot points\u003c\/li\u003e \u003cli\u003eStainless steel spring returns engine to idle position when released\u003c\/li\u003e \u003cli\u003eEquipped with toe clip for additional safety in extreme conditions\u003c\/li\u003e \u003cli\u003eMounts directly to floor of boat with four screws (not included)\u003c\/li\u003e \u003cli\u003eUses standard control cables for easy hook-up\u003c\/li\u003e \u003cli\u003ePatened Idle Stop for FICHT and Optimax engines\u003c\/li\u003e \u003c\/ul\u003e \u003chr\u003e \u003ch2\u003eHow to Install T-H Marine Hot Foot Original Foot Throttle\u003c\/h2\u003e \u003cul\u003e \u003cli\u003eSelect a mounting location that is comfortable and install mounting screws (not included).\u003c\/li\u003e \u003cli\u003eMounting location should be such that there are no sharp bends in cable to cause binding or friction.\u003c\/li\u003e \u003cul\u003e \u003cli\u003e\n\u003cstrong\u003eNOTE:\u003c\/strong\u003e The Hot Foot will require a throttle cable that is 2 feet longer than shift cable. Remove throttle cable from engine and replace with longer cable.\u003c\/li\u003e \u003c\/ul\u003e \u003cli\u003eSelect cable location by engine type:\u003c\/li\u003e \u003c\/ul\u003e \u003ctable style=\"height: 370px; ; width: 100%;\" border=\"0\"\u003e \u003ctbody\u003e \u003ctr\u003e \u003ctd\u003e \u003cul\u003e \u003cul\u003e \u003cli\u003e\u003cstrong\u003eMercury except Gen II:\u003c\/strong\u003e\u003c\/li\u003e \u003cul\u003e \u003cli\u003eInsert throttle cable trunnion into \u003cstrong\u003e2\u003c\/strong\u003e upper trunnion holder on side plate and install cotter pin to retain trunnion.\u003c\/li\u003e \u003cli\u003eBend cotter pin to keep in place.\u003c\/li\u003e \u003c\/ul\u003e \u003cli\u003e\u003cstrong\u003eHonda, Mercury Gen II, Suzuki, or Pull Type Throttle Using 3300 Series Cable:\u003c\/strong\u003e\u003c\/li\u003e \u003cul\u003e \u003cli\u003ePosition cable so that cable clamp \u003cstrong\u003eC\u003c\/strong\u003e fits into groove in trunnion area of cable.\u003c\/li\u003e \u003cli\u003eReplace clamp and screws to side plate \u003cstrong\u003e1\u003c\/strong\u003e.\u003c\/li\u003e \u003cli\u003eScrew cable end \u003cstrong\u003eD\u003c\/strong\u003e onto end of cable slide and tighten to lock nut against cable end.\u003c\/li\u003e \u003c\/ul\u003e \u003cli\u003e\u003cstrong\u003eOMC:\u003c\/strong\u003e\u003c\/li\u003e \u003cul\u003e \u003cli\u003eInsert throttle cable trunnion into \u003cstrong\u003e3\u003c\/strong\u003e lower trunnion holder on side plate and install cotter pin to retain trunnion.\u003c\/li\u003e \u003cli\u003eBend cotter pin to keep in place.\u003c\/li\u003e \u003c\/ul\u003e \u003cli\u003e\u003cstrong\u003eYamaha, Chrysler, or Push Type Throttle Using 3300 Series Cable:\u003c\/strong\u003e\u003c\/li\u003e \u003cul\u003e \u003cli\u003ePosition cable so that cable clamp \u003cstrong\u003eC\u003c\/strong\u003e fits into groove in trunnion area of cable.\u003c\/li\u003e \u003cli\u003eReplace clamp and screws to side plate \u003cstrong\u003e4\u003c\/strong\u003e.\u003c\/li\u003e \u003cli\u003eScrew cable end \u003cstrong\u003eD\u003c\/strong\u003e onto end of cable slide and tighten lock nut against cable end.\u003c\/li\u003e \u003c\/ul\u003e \u003c\/ul\u003e \u003c\/ul\u003e \u003c\/td\u003e \u003ctd\u003e \u003cp\u003e\u003cimg class=\"__mce_add_custom__\" title=\"TH Marine Hot Foot Install\" src=\"https:\/\/cdn11.bigcommerce.com\/s-6rtev5owwo\/product_images\/uploaded_images\/hf-1-dp.3.jpg\" alt=\"TH Marine Hot Foot Install\" width=\"362\" height=\"365\"\u003e\u003c\/p\u003e \u003c\/td\u003e \u003c\/tr\u003e \u003c\/tbody\u003e \u003c\/table\u003e \u003cul\u003e \u003cli\u003eInstall 1\/4-20 x 1\" bolt through cable end.\u003c\/li\u003e \u003cli\u003eThread 1\/4-20 nut onto bolt and screw bolt into the upper end \u003cstrong\u003e1a\u003c\/strong\u003e of pivot arm (Honda, Suzuki, Mercury), or lower end \u003cstrong\u003e4a\u003c\/strong\u003e of pivot arm (OMC, Yamaha, Chrysler) until bolt is flush with back side. Tighten hex nut to lock assembly in place.\u003c\/li\u003e \u003cli\u003eOperate Hot Foot Throttle by hand to determine if cable operation is smooth and travel is adequate top open linkage on engine to full throttle.\u003c\/li\u003e \u003cli\u003eSpring tension may also be adjusted to achieve a smooth return to idle when pedestal is released.\u003c\/li\u003e \u003cli\u003eAll moving parts and pivot points should be lubricated with a quality marine lubricant periodically. \u003c\/li\u003e \u003c\/ul\u003e \u003cp\u003eThis information and more is provided on the back of the T-H Marine Hot Foot packaging. \u003c\/p\u003e","brand":"T-H Marine","offers":[{"title":"Default Title","offer_id":67606290170171,"sku":"T-H-HF-1","price":323.49,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0907\/4271\/8779\/files\/HF-1-DP__39439.1737837969.jpg?v=1790719674","url":"https:\/\/clinchriverfishingusa.com\/products\/t-h-marine-hot-foot-john-evin-merc-t-h-hf-1","provider":"Clinch River Fishing USA","version":"1.0","type":"link"}